Postgraduate Diploma in DCT/CVT for 2R and Quickshifter
Online 800-hour Postgraduate Diploma in DCT/CVT for 2R and Quickshifter. 8 modules covering ISO 26262-12:2018, ISO 6336-1 and MATLAB/Simulink. Assigned tutor and enrolment open.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Compare the transmission architectures used in two-wheeled vehicles.
Tune CVT variators through the analysis of rollers and springs.
Explain the operation and control of dual-clutch gearboxes.
Calibrate quickshifters and blippers for upshifts and downshifts.
Develop transmission control strategies in a simulation environment.
Calculate gears and shafts according to international standards.
Plan the functional and mechanical validation of a transmission.
Who it's for
- Transmission engineer wishing to specialise in DCT/CVT for 2R and Quickshifter.
- Transmission control engineer wishing to specialise in DCT/CVT for 2R and Quickshifter.
- Calibration engineer wishing to specialise in DCT/CVT for 2R and Quickshifter.
- Gear designer wishing to specialise in DCT/CVT for 2R and Quickshifter.
- Validation engineer wishing to specialise in DCT/CVT for 2R and Quickshifter.
- Embedded software engineer wishing to specialise in DCT/CVT for 2R and Quickshifter.
- Graduates in engineering or sciences seeking to enter motorcycle manufacturing.
What you'll work with
- ISO 26262-12:2018
- ISO 6336-1
- ISO 6336-2
- ISO 1328-1
- ISO 281
- JASO T903
- Delegated Regulation (EU) No 3/2014
- UN R60
8 modules · 800 h
1.1Constant-mesh sequential gearboxes1.2Gear ratios and spacing1.3Secondary drive by chain, belt and shaft1.4Mechanical losses in the transmission1.5Automatic architectures in scooters1.6Transmissions for electric motorcycles1.7Mass and cost comparison1.8User experience and market1.9Centrifugal automatic clutches1.10Workshop: gear spacing for a given engine
2.1Variable pulleys and V-belt2.2Centrifugal rollers and shift curves2.3Back-pressure spring and centrifugal clutch2.4Belt losses and efficiency2.5Roller and belt wear2.6Electronically controlled CVT2.7Acceleration response simulation2.8Roller and spring tuning2.9Final drive and wheel diameter2.10Practice: selecting roller mass
3.1Dual-clutch principle3.2Multi-plate wet clutches3.3Hydraulic and electrohydraulic actuation3.4Gear preselection3.5Overlap control during shifting3.6Manual and automatic modes3.7Starting and low-speed manoeuvring3.8Clutch thermal management3.9Dry versus wet clutches in DCT3.10Laboratory: simulation of an overlap shift
4.1Load sensors on the shift lever4.2Ignition and injection cut-off4.3Cut duration by gear and speed4.4Downshift with throttle blip4.5Ride-by-wire and torque control4.6Interaction with traction control4.7Reliability of sensors and connectors4.8Aftermarket versus OEM systems4.9Shift strategies in corners4.10Case study: calibrating cut times
5.1Gear selection strategies5.2Detection of rider intent5.3Adaptation to clutch wear5.4Clutch pressure control5.5Transmission models in Simulink5.6Communication with engine ECU5.7Fault management and limp-home mode5.8Software testing in HIL5.9Automatic shifting in multi-speed electric motorcycles5.10Practice: shift strategy in Simulink
6.1Spur and helical gears6.2Bending strength and contact pressure6.3Pitting, micropitting and scuffing6.4Shift forks and selector drum6.5Bearings and rated life6.6Lubrication and wet clutch oils6.7Gear noise and vibration6.8Tolerances and gear quality6.9Straight-cut gears in competition6.10Workshop: calculation of a gear pair
7.1Bench durability tests7.2Vehicle and rider tests7.3Shift quality and subjective assessment7.4Functional safety of the transmission7.5Motorcycle control requirements7.6On-road noise tests7.7Diagnostics and maintenance7.8Variant management7.9Acceleration noise regulations7.10Case study: validation plan for a quickshifter
8.1Selection of vehicle and transmission8.2Performance and comfort requirements8.3Design of gear ratios8.4Shift control strategy8.5Quickshifter calibration8.6Verification of mechanical components8.7Validation plan8.8Cost analysis8.9Report and presentation8.10Final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetables: students progress at their own pace within the intake, which makes it possible to combine the programme with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is MATLAB/Simulink, Romax Spectrum, KISSsoft, ETAS INCA, GT-SUITE, in free, academic or evaluation versions. Tests are studied using real clutch durability procedures on transmission test benches, quickshifter cut calibration on roller dynamometers, and subjective shift-quality assessment with riders. Assessment is continuous per module plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Compare the transmission architectures used in two-wheeled vehicles.
Tune CVT variators through the analysis of rollers and springs.
Explain the operation and control of dual-clutch gearboxes.
Calibrate quickshifters and blippers for upshifts and downshifts.
Develop transmission control strategies in a simulation environment.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. A university degree is not required.
- Internet connection and a computer capable of running the programme software.
- Sufficient Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours spread over 6 to 8 months. That is between 10 and 15 hours per week on average, compatible with a full-time job.
You work with MATLAB/Simulink, Romax Spectrum, KISSsoft, ETAS INCA, GT-SUITE. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM Institute own diploma upon passing the continuous assessment and the integrative project. This is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised in the higher-level programme. Check the recognition policy when you enrol.
Related programmes
Postgraduate Diploma in Chassis Vibrations and Isolation
Online Postgraduate Diploma of 800 hours in Chassis Vibrations and Isolation. 8 modules covering ISO 5349-1, ISO 2631-1 and Simcenter Testlab. Assigned tutor and open enrolment.
Postgraduate Diploma in Automation/MES for PTW
Online 800-hour postgraduate diploma in automation/MES for PTW. 8 modules covering IEC 62264-1:2013 (ISA-95), IEC 61131-3:2013 and Siemens TIA Portal. Assigned tutor and open enrolment.
Postgraduate Diploma in Motorcycle UX: Navigation and HMI with Gloves
Online 800-hour Postgraduate Diploma in Motorcycle UX: Navigation and HMI with Gloves. 8 modules covering ISO 15008, ISO 15005 and Figma. Assigned tutor and enrolment open.
More in Motorcycles & 2-Wheelers
All Motorcycles & 2-Wheelers programmes → · How to apply · Fees & financing · Scholarships