Postgraduate Diploma in Batteries, IP Rating and Anti-Vandalism
Online 800-hour Postgraduate Diploma in batteries, IP Rating and Anti-Vandalism. 8 modules covering IEC 60529:1989+A2:2013, IEC 62262:2002 and SolidWorks. Assigned tutor and open enrolment.
Take the controls.
Run a real engineering trade-off from this field. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Size interchangeable battery packs for intensive use.
Design sealed housings with suitable gaskets and cable glands.
Specify and verify IP and IK protection ratings.
Assess mechanical robustness against drops, vibration and impacts.
Apply anti-vandalism and anti-theft design solutions.
Establish safety protocols for battery storage and charging.
Plan the validation and certification of vehicles for shared fleets.
Who it's for
- Battery engineer looking to specialise in Batteries, IP Rating and Anti-Vandalism.
- Mechanical design engineer looking to specialise in Batteries, IP Rating and Anti-Vandalism.
- Environmental testing engineer looking to specialise in Batteries, IP Rating and Anti-Vandalism.
- Sharing product manager looking to specialise in Batteries, IP Rating and Anti-Vandalism.
- Operations safety technician looking to specialise in Batteries, IP Rating and Anti-Vandalism.
- Validation engineer looking to specialise in Batteries, IP Rating and Anti-Vandalism.
- Graduates in engineering or sciences seeking to enter shared micromobility operators.
What you'll work with
- IEC 60529:1989+A2:2013
- IEC 62262:2002
- UN 38.3 (UN Manual of Tests and Criteria)
- IEC 62133-2:2017
- EN 50604-1:2016
- ISO 20653:2023
- UNE-EN 17128:2021
- Reglamento (UE) 2023/1542
8 modules · 800 h
1.1Cylindrical and prismatic cells1.2LFP versus NMC chemistry1.3Series-parallel pack configuration1.4Management system and protections1.5Design of swappable batteries1.6Intensive use and degradation1.7Thermal safety and propagation1.8UN 38.3 transport tests1.9Requirements of EN 50604-11.10Practical: sizing a swappable pack
2.1Aluminium, PC and reinforced polyamide housings2.2O-rings and silicone gaskets2.3Connector and cable gland sealing2.4Vent membranes2.5Condensation prevention2.6Paint and corrosion protection2.7Housing heat dissipation2.8Access for quick maintenance2.9Gasket compression and tolerances2.10Workshop: designing the gasket of a battery compartment
3.1IP code and the meaning of its digits3.2Dust tests in chamber3.3Jet and immersion tests3.4IPX9K high-pressure test3.5Differences between IEC 60529 and ISO 206533.6Sealing after ageing and vibration3.7Common sealing failures3.8Fleet pressure washing3.9Leak detection by pressure drop3.10Laboratory: IPX5 test of a controller
4.1IK code and impact tests4.2Vehicle drops and tip-overs4.3Cobblestone vibration4.4Shocks in transport and loading4.5Impact simulation with LS-DYNA4.6Pack protection against puncture4.7Mounts and anchorages4.8Fastener fatigue4.9Crush tests4.10Practical: lateral impact simulation of the pack
5.1Types of vandalism in shared fleets5.2Security fasteners and hidden access5.3Cable and connector protection5.4Screens and exposed elements5.5Materials resistant to cuts and graffiti5.6Padlocks and wheel locking5.7Secure anchorages against battery theft5.8Tamper detection and alarms5.9Cost of vandalism per vehicle5.10Case study: anti-vandalism redesign of a shared e-scooter
6.1Fire risk in storage6.2Detection of damaged cells6.3Depot charging protocols6.4Quarantine containers6.5Response to thermal runaway6.6Operations staff training6.7Insurer and fire service requirements6.8Transport of damaged batteries6.9Incident recording and analysis6.10Workshop: emergency plan for a battery depot
7.1Product validation plan7.2Combined environmental testing7.3Durability in a pilot fleet7.4Battery certification7.5Obligations under the Batteries Regulation7.6Technical product documentation7.7Field failure analysis7.8Iterative design improvement7.9Municipal tender requirements7.10Case study: validation of a sharing e-scooter
8.1Fleet requirements8.2Battery pack design8.3Housing and sealing8.4Impact protection8.5Anti-vandalism and anti-theft measures8.6Operational safety protocol8.7Validation plan8.8Cost and maintenance8.9Report and presentation8.10Final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetable: students progress at their own pace within the intake, which makes it possible to combine study with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is SolidWorks, COMSOL Multiphysics, Ansys LS-DYNA, MATLAB, in free, academic or evaluation versions. Tests are studied using real procedures: IPX5 water-jet test on a controller, lateral impact simulation of a battery pack, and anti-vandalism redesign of a shared e-scooter. Assessment is continuous by module plus the final integrating project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Size interchangeable battery packs for intensive use.
Design sealed housings with suitable gaskets and cable glands.
Specify and verify IP and IK protection ratings.
Assess mechanical robustness against drops, vibration and impacts.
Apply anti-vandalism and anti-theft design solutions.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient Spanish to follow technical standards documentation.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme comprises 800 hours in total, spread over 6 to 8 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
You will work with SolidWorks, COMSOL Multiphysics, Ansys LS-DYNA and MATLAB. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
A SEIUM Institute diploma upon passing continuous assessment and the integrating project. It is in-house training, not an official qualification from the Ministry.
Yes. Modules passed in a course or postgraduate diploma in the same area are recognised towards the higher-level programme. Check the recognition policy when you enrol.
Related programmes
Postgraduate Diploma in EFI/GDI 2R and Knock Control
Online 800-hour Postgraduate Diploma in EFI/GDI 2R and Knock Control. 8 modules covering Delegated Regulation (EU) No 134/2014, ISO 26262-12:2018 and ETAS INCA. Assigned tutor and…
Postgraduate Diploma in Driving Ergonomics and Fatigue Prevention
Online 800-hour Postgraduate Diploma in Driving Ergonomics and Fatigue Prevention. 8 modules covering ISO 2631-1:1997, ISO 5349-1:2001 and Siemens Tecnomatix Jack. Personal tutor assigned and enrolment…
Postgraduate Diploma in Brand Identity and 2R Surfaces
800-hour online Postgraduate Diploma in Brand Identity and 2R Surfaces. 8 modules covering UNECE Regulation No. 53, UNECE Regulation No. 81 and Autodesk Alias. Assigned tutor…
More in Motorcycles & 2-Wheelers
All Motorcycles & 2-Wheelers programmes → · How to apply · Fees & financing · Scholarships