Postgraduate Diploma in Acceleration Data and ET/Trap Speed Optimisation
Online 800-hour Postgraduate Diploma in Acceleration Data and ET/Trap Speed Optimisation. 8 modules covering the NHRA Rulebook, the FIA European Drag Racing Championship Regulations and Racepak DataLink II. Dedicated tutor and open enrolment.
Take the controls.
Run a real engineering trade-off from this programme. Move the sliders, watch the model react in real time and beat the challenge.
What you will be able to do
Interpret drag racing time and speed metrics.
Install acceleration data acquisition systems.
Analyse the launch phase using data.
Calculate shift points and effective power.
Model and predict ET with atmospheric corrections.
Optimise vehicle setup.
Improve consistency in bracket competitions.
Who it's for
- Acceleration data engineer who wants to specialise in Acceleration Data and ET/Trap Speed Optimisation.
- Drag racing performance analyst who wants to specialise in Acceleration Data and ET/Trap Speed Optimisation.
- Crew chief who wants to specialise in Acceleration Data and ET/Trap Speed Optimisation.
- Data acquisition technician who wants to specialise in Acceleration Data and ET/Trap Speed Optimisation.
- Vehicle preparer who wants to specialise in Acceleration Data and ET/Trap Speed Optimisation.
- Bracket racing driver who wants to specialise in Acceleration Data and ET/Trap Speed Optimisation.
- Graduates in engineering or sciences seeking to enter drag racing.
What you'll work with
- NHRA Rulebook
- FIA European Drag Racing Championship Regulations
- SFI Spec 25.1 chassis
- SFI Spec 16.1 harnesses
- SFI Spec 3.2A fire suits
- SFI Spec 1.1 steering wheels and clutches
8 modules · 800 h
1.1Reaction time and red light1.260-foot time1.3Intermediate times at 330 and 660 feet1.4ET at 1000 feet and quarter mile1.5Trap speed and its measurement1.6ET–trap speed relationship and power1.7Performance index by class1.8Consistency between runs1.9Complete time slip1.10Practice: interpreting a series of time slips
2.1Acceleration-specific data loggers2.2Wheel speed sensors2.3Engine and shaft RPM sensors2.4Longitudinal accelerometers and their mounting2.5Chassis ride-height sensors2.6Boost and fuel pressures2.7Exhaust gas temperature2.8Appropriate sampling rate2.9Installation and wiring2.10Workshop: installing a Racepak system
3.1Tyre slip at launch3.2RPM curve after launch3.3Longitudinal acceleration over the first metres3.4Front wheel lift3.5Relationship between 60-foot time and final ET3.6Diagnosing bog and shudder3.7Influence of track preparation3.8Run comparison3.9Data-based launch adjustments3.10Laboratory: tyre slip analysis using wheel data
4.1Speed versus distance curve4.2Optimal shift points4.3RPM drop between gears4.4Effective power derived from data4.5Aerodynamic losses in the final section4.6Influence of weight on trap speed4.7Power calculation from trap speed4.8Detecting power loss4.9Comparison with simulation4.10Practice: calculating optimal shift points
5.1Longitudinal equations of motion5.2Traction and slip models5.3Aerodynamic and rolling resistance5.4Air density correction5.5Dial-in prediction5.6Regression with historical data5.7Simulating setup changes5.8Model validation5.9Limitations of prediction5.10Laboratory: ET prediction model in Python
6.1Final drive ratio6.2Rear tyre diameter6.3Weight reduction and its effect6.4Converter and clutch adjustments6.5Phased power adjustments6.6Wheelie bar and wing aerodynamics6.7Weather-based strategy6.8Structured test plan6.9Change log6.10Case study: final drive ratio optimisation
7.1Run-to-run variability7.2Statistical control of times7.3Dial-in and bracket strategy7.4Reaction time and training7.5Factors affecting consistency7.6Engine management between rounds7.7Technical test diary7.8Decisions in eliminator rounds7.9Driver psychology7.10Practice: statistical consistency analysis
8.1Vehicle selection and baseline data8.2Analysis of reference runs8.3Loss diagnosis8.4Proposed changes8.5Improvement simulation8.6Track validation8.7Technical results report8.8Development recommendations8.9Report and presentation8.10Final review with the tutor
How you'll learn
100% online training on the SEIUM campus, with downloadable material, recorded classes and an assigned technical tutor. No fixed timetables: students progress at their own pace within the intake, which makes it possible to combine the programme with work.
Each module combines theory, guided reading of the original standard and applied exercises. The working software is Racepak DataLink II, Performance Trends Drag Racing Analyzer, Python with pandas, MATLAB, Microsoft Excel, in free, academic or evaluation versions. Tests are studied using real procedures for single-run acceleration data analysis, ET prediction through models and optimisation of gear ratios. Assessment is continuous per module plus the final integrative project.
Build it end to end
Your final project follows the real engineering workflow, step by step, reviewed by your tutor.
Interpret drag racing time and speed metrics.
Install acceleration data acquisition systems.
Analyse the launch phase using data.
Calculate shift points and effective power.
Model and predict ET with atmospheric corrections.
Where this takes you
Requirements
- Prior technical training or professional experience in the sector. No university degree is required.
- Internet connection and a computer capable of running the programme's software.
- Sufficient level of Spanish to follow technical standards reading.
Ready to start?
Send your application today. Our admissions team replies within 72 hours with your study plan and funding options.
Frequently asked questions
The programme totals 800 hours spread over 6 to 8 months. That is an average of 10 to 15 hours per week, compatible with a full-time job.
You will work with Racepak DataLink II, Performance Trends Drag Racing Analyzer, Python with pandas, MATLAB and Microsoft Excel. Free, academic or evaluation versions are used, and the tutor indicates the free alternative where one exists.
An own diploma from SEIUM upon passing the continuous assessment and the integrative project. It is in-house training, not an official Ministry qualification.
Yes. Modules passed in a course or diploma in the same area are credited towards the advanced programme. Check the credit transfer policy when you enrol.
Related programmes
Postgraduate Diploma in Multispectral Signature Management (IR, Radar, Optical)
Online Postgraduate Diploma of 800 hours in Multispectral Signature Management (IR, radar, optical). 8 modules covering IEEE 686 (standardised radar definitions), ASTM E1933 (emissivity measurement with…
Postgraduate Diploma in Set-Up for Sprint and Endurance Touring Cars
Online 800-hour Postgraduate Diploma in Set-Up for Sprint and Endurance Touring Cars. 8 modules covering the FIA International Sporting Code, Appendix J, Article 253: safety equipment…
Postgraduate Diploma in Traceability, Batch Management and On-Track Dimensional Control
Online Postgraduate Diploma of 800 h in Traceability, Batch Management and On-Track Dimensional Control. 8 modules covering ISO 9001:2015 quality management systems, AS9100D aerospace quality management…
More in Automotive & Motorsport
All Automotive & Motorsport programmes → · How to apply · Fees & financing · Scholarships